Can You Set Up an Inflatable Pool on Concrete?

One thing certain is that nobody wouldn’t like to have a cool refreshment after a rough day of summer weather.

This is possible when you have a well-installed pool for swimming. If you don’t level your pool properly, you may end up with an unappreciated pool because a pool that is installed properly is always safe and fun to swim in.

If you have a good concrete block for your inflatable pool, you can put it on it, mind you, it should be on a smooth block. For excellent work, it must be on a smooth and leveled slab.

So, you could check out your concrete first before processing your work. However, in this article, we will show you how to level your inflatable pool on concrete.

Can You Put an Inflatable Pool on Concrete?

Of course, yes, you can place your inflatable pool on a concrete floor. Indeed, it is one of the best to use for leveling your inflatable pool.

To place an inflatable pool on concrete will require you to use a groundsheet or cloth to secure the pool from damage due to the contact on an unsmooth concrete.

A well-leveled concrete floor is highly approved for installing an inflatable pool because of balance. So, you won’t be required to do any additional work on maintaining balance.

What To Use for Leveling?

If you want to use sand to level your inflatable pool, all you have to do is clear the place you tend to install your inflatable pool and pour your sand.

It should give you a leveled ground when done accurately. However, sand could lose its particle easily due to some critters under the pool and may cause damage to your pool.

Sand tends to move easily from the place you place it. So, it is not advisable to use sand over concrete.

Concrete is the easiest way to level your inflatable pool on the ground. Concrete is easier to become smooth, and its uneven surface makes the pool stable irrespective of the number of people in the pool.

Though, its uneven surface also turns out to be a big problem of damage due to constant touch on the concrete surface. Below are tools or materials to use for leveling.

Rake
Shovell
Bubble Level
Tent pole
Drill and Bits
Washers

How to Set Up an Inflatable Pool on Concrete

STEP 1: Determine your location and clear

Pick a site in your backyard that is leveled and away from trees, and make sure the ground is dense enough with good soil for your inflatable pool.

You can now remove grasses with a shovel and use a rake to remove rock or any waste around the place.

The grasses could be relocated to another spot where you allow them to dry and get them burnt.

You already know that before then, you have to map out the site and measure it with a tape rule to get a length for your inflatable.

STEP 2: Leveling the site

Trying to level the ground with just sight is not advisable, which means a single assumption could cause a problem to your inflatable pool.

All you have to do is place a plank or a level on the site to ensure it is level. You can commerce with a rod on the center of the place and at each edge with a cord connected to the rods depending on the shape of your inflatable pool.

When it comes to leveling, there are many things to consider, such as wire levels, floating slap, and water extent.

It’s all about setting up the place with a center clip that could oscillate like a clock. You could aim at using 8 of 2″ by 4″ length, which may be tied to the top as straight as possible.

The center clip should be joined with an extra tent rope to straight up to the wooden pole. Make necessary adjustments is required.

STEP 3: Making the Stake

The stake shape is constructed by tilt carving to the table saw and the exploratory drill hole instructed and focused on both directions of about two by four lengths.

Then the arm connected to a 3/8″ hole across the open sides. You can make a drilled pilot, which is just an additional scrap of 2 by four if you don’t have the means of support the two by four length with a drill press.

STEP 4: Setting the Stake and Leveling Arm

The stake should be screwed in the center point with a cutter. Turn up the top with wires on the area to help it level.

As it is the place of rotation, it’s good to slightly place the tent stake (center pin) and inspect it for plumb level. Then, a washer should be placed up and down of the arm when adding the pin.

The tapping should be in the end small bit with sled and around the armed middle, position the level and fix it in place with a tape, but it should be in a position facing upward so it could be easy to view when standing.

STEP 5: Final setup and leveling

It’s time you removed any debris or dirty you may not have removed. Then start to rotate the arm around the site higher.

It is advisable to use a shovel to move the soil till the bubble no longer touches the lines. Getting closer to the level, the arm may form irregularity in the site.

You can use the arm to smooth some dirt on the place to avoid gaps. Mind you; the arm can move earth like a small front-end loader.

Though it may take a little while to project concrete and all that, you still have to be certain if you are joining clay back that you crowd down the place severally.

Flumping will, however, take place still could be reduced as quickly before the weight of the pool worsens. If you have a tamper, you could use it.

STEP 6: Rounding off

Proceed with laying the groundsheet if it is well leveled. Ensure there is no wrinkled place to avoid affecting the down of the pool.

By the way, you can make sure there are no wrinkles by balancing each side with bricks in all directions. Then spread out your inflatable pool across the tarp.

It is best to spread the pool on another side for some minutes to be touched a beat by the sun before placing it over the site to avoid wrinkles.

Create a position that will fit the inlet and outlet pipe control with filter and chlorine alternator to make it easier for you to fill or empty the pool. You will get a nice feeling of how well it’s being leveled when water starts filling.

Intex Pool on Unlevel Concrete

Intex pool or any other above-ground pool should not be in a block of unlevel concrete.

Nevertheless, Intex and other pool companies provide their customer with leeway to set it on unlevel concrete.

Setting Intex pool on a slopy place may not matter so long it is well leveled.

Risks of Intex Pool on Unlevel Concrete

Here are common risks associated with the Intex pool on uneven concrete.

1. Maybe dangerous to children:

Unleveled Intex pool will be very risky to children be the wall of the pool will not be balanced as supposed to, and because of it, children cannot reach the deeper base of the pool.

Also, the high risk of collapsing at any time may be a trait to kids while swimming. So, you should try as much as possible to level the area to set your Intex pool.

2. It causes damage to your pool liner:

The pool liner is another part that will certainly get destroyed by unlevel concrete because it may have wrinkled on it.

How durable your pool linear is does not stop it, so you should avoid the risks of damaging your inflatable pool quickly during washing or scrubbing.

3. Problem with your pool wall:

This is one of the problems of uneven concrete. It tends to exert pressure on the wall of the pool by lowering one part than the other. This will cause your pool to fall easily, especially inflatable.

Can You Set Up Above Ground Pool on Concrete?

Although, above ground pool is mostly built on the ground or the sand. Yes, it is safe and easy to install above ground pool on a block of concrete.

Yet there are some things to do and not when deciding and you should be aware of some certain somethings some have been mentioned earlier.

The lifespan of Above Ground Pool

An average above-ground pool will last for about 10 to 15 years before becoming weak. The pool liners will last up to 6 to 8 years, and after they need to be replaced with a new one, the in-ground system may last up to 20 years and above.

Is Installing an Oval Pool on Concrete Hard?

Oval pool’s design may amount to some side to be under the base path. They are not mostly built on a one-level or plane place.

So, an oval pool cannot be installed on a concrete block even if it is perfectly leveled.

However, it may be approved if you build a sandbox, but cutting the pool to lie perfectly on the level is very difficult.

CONCLUSION

Levelling your inflatable pool on concrete in your backyard is nice and safe, especially in summer. Since it is leveled, swimming on it is pretty cool, especially for kids.

However, hope this article is helpful. I’d like to hear your point on how to level an inflatable pool on a block of concrete.

You May Also Like:

We hope this article helped you decide if it’s proper to set up an inflatable pool on concrete? You may also want to bookmark our reviews on Slammo vs Spikeball Review.

I will love to hear from you if you have any other suggestions on Inflatable Pool on Concrete, all you have to do is comment below. Do well to connect those who need this article by sharing it on your social media platforms like Twitter and Facebook.

If you liked this article, then please follow us on Facebook, Instagram and Pinterest.